Voyager 2.5 td 94-2000 регулировка троса коробки |
Здравствуйте, гость ( Вход | Регистрация )
Voyager 2.5 td 94-2000 регулировка троса коробки |
17.3.2017, 17:15
Сообщение
#1
|
|
Прописался Группа: Пользователи Сообщений: 120 Регистрация: 19.8.2013 Пользователь №: 64 647 |
Помогите разобраться , не могу понять как правильно регулировать со стороны салона трос переключения .
Может <англичане > )) подключатся и переведут текст в рамке ? Сообщение отредактировал blijnii - 17.3.2017, 17:24 |
|
|
17.3.2017, 17:29
Сообщение
#2
|
|
Прописался Группа: Пользователи Сообщений: 120 Регистрация: 19.8.2013 Пользователь №: 64 647 |
GEARSHIFT LINKAGEADJUSTMENT (CABLEOPER-
ATED) Before replacing the gearshift selector cable or cross- over cable for a hard-shifting complaint, disconnect both cables at the transaxle (Fig. 3). Then, from the driver’s seat, manually operate the gearshift lever through all gear ranges. If the gearshift lever moves smoothly, the cable(s) should NOT be replaced. (1) Working over the left front fender, remove the lock pin from the transaxle gearshift (selector shaft) housing (Fig. 4). (2) Reverse the lock pin (so long end is down) and insert lock pin into same threaded hole. A hole in the selector shaft will align with the lock pin, allowing the lock pin to be screwed into the housing. This operation locks the selector shaft in the 3-4 neutral position. (3) Remove or install gearshift knob (Fig. 5 or 6). (4) Remove or install boot (Fig. 7). (5) Remove or install selector and crossover cables (Fig. 8 or 9). Cable attachment clips must be installed from the side. Install cable fittings to shifter pins by pushing with thumb. CAUTION: Be sure crossover bellcrank does NOT move when tightening adjusting screw (Fig. 10) CAUTION: Proper torque to the crossover cable ad- justing screw is very important (Fig. 10). (6) Remove lock pin from gearshift housing and reinstall lock pin (so long end is up) in gear shift housing (Fig. 4). Tighten lock pin to 8 NIm (70 in. lbs.). (7) Check for shift into first and reverse. Check for blockout into reverse. ( Gearshift mechanism and cables are now func- tioning properly. |
|
|
17.3.2017, 17:49
Сообщение
#3
|
|
Прописался Группа: Пользователи Сообщений: 120 Регистрация: 19.8.2013 Пользователь №: 64 647 |
И еще , болтается лапка относительно валика переключения ,приблизительно 2-3 мм по окружности в обе стороны . Смотрите пожалуйста рисунок по ссылке , сюда загружаться не хочет (((
Вот ссылка. https://yadi.sk/i/EIdHSlSK3G6jJv Сообщение отредактировал blijnii - 17.3.2017, 17:50 |
|
|
22.3.2017, 23:14
Сообщение
#4
|
|
Прописался Группа: Пользователи Сообщений: 120 Регистрация: 19.8.2013 Пользователь №: 64 647 |
100 просмотров и ни одного ответа.. Никто не знает за коробку ничего ((
|
|
|
Текстовая версия | Сейчас: 19.4.2024, 14:37 |
Мы в соцсетях: |